Recessed entrance mat with brush insert 17/30 mm STABLE and aluminium angle frame: R13, Bfl-s1, 2000 kg/dm², Zones 1–3, 4 colours. Order now, made to measure.
The STABLE 17/30 recessed entrance mat with cassette brush is the brush solution for high-footfall entrance areas with heavy coarse dirt loads. The double-supported rectangular hollow aluminium profile with internal reinforcing webs (profile height 17 mm × profile width 30 mm) withstands a permissible dynamic load of 2000 kg/dm²; the finished aluminium profile mat has an overall height of 27 mm. The cassette brush made of Moplen EP440G mechanically removes mud, snow, leaves and small stones from the soles of shoes and, at R13 according to DIN 51130, achieves the highest slip resistance class in the Alukraft range; its reaction to fire class is Bfl-s1 according to DIN EN 13501-1. The 3 mm EPDM impact sound insulation on the underside keeps footsteps quiet. Set in the precisely fitting aluminium angle frame with a frame height of 21 mm, the entrance mat sits flush in the mat well and finishes level with the surrounding floor covering without creating a trip hazard.
Within the 17/30 profile, the brush insert version is the most mechanically aggressive and, at R13, the most slip-resistant variant – the rib carpet (25 mm, R11) is restricted to Zones 2 and 3 in all series and absorbs moisture rather than scraping off coarse dirt, while the vinyl rubber insert (24 mm, R10) is also suitable for wheeled traffic but cleans less intensively by mechanical action. This version is therefore recommended as the first cleaning zone, directly in front of or at the entrance. Compared with the STANDARD 19/30 brush mat, which has the same overall height of 27 mm, the same footfall, the same slip resistance class and the same 21 mm aluminium frame, STABLE 17/30 is designed for 2000 kg/dm² instead of 1200 kg/dm², features EPDM impact sound insulation instead of polypropylene foam, is classified Bfl-s1 for reaction to fire and is optionally available with a stainless steel frame and black anodised or powder-coated support profiles. If you want the same values with a wider tread surface, choose BÜRSTE STABLE XL 17/50 (aluminium profile mat with brush insert); both profile widths can also be combined as a MIX in a single area.
The cassette brush is approved for use in indoor and outdoor areas – Zones 1, 2 and 3. It is particularly effective against coarse dirt, mud, snow and leaves; it is recommended as the first cleaning zone. The mat is not designed for forklift trucks or construction hoists.
The 17/30 profile is designed for a footfall of up to 10,000 people per day and more. Typical buildings in this footfall range are stadiums, arenas, exhibition grounds, congress centres, airports, major railway stations and shopping centres; for these, a barrier matting area of 48–64 m² spread across several zones is recommended. The same system is equally suitable for lower footfall – for example with 27–36 m² in railway stations, universities, hospitals, and resort and spa centres, or with 12–18 m² in office complexes, hotels, government agencies, public authorities, schools and public facilities. Combining several zones achieves a dirt retention of 70 to 90 %.
Option A – aluminium angle frame (version of this product): The angle frame is set into a mat well and the aluminium profile mat is laid in with a precise fit. The STABLE 17/30 profile uses the aluminium angle frame with a frame height of 21 mm, so the minimum installation depth is 21 mm. The frame is supplied with corner connectors, straight connectors and floor anchors, with pre-drilling on request; concrete anchors allow drill-free installation followed by levelling and grouting in with cement mortar. Alternatively, a 25 mm high stainless steel frame is available, supplied as four elements and joined on site. Black anodised angle frames are available for the STABLE series on request.
Option B – ramp profile (alternative without a mat well): The mat is laid directly on the existing substrate; the ramp profile forms a threshold ramp and allows accessible use, including with wheelchairs, shopping trolleys or wheeled suitcases. The ramp profile is selected according to the profile height of the support profile – 17 mm for this product. Depending on the substrate, it is fixed with construction adhesive or expansion plugs. No angle frame is used in this option.
Option C – dirt collection tray (alternative for heavy dirt loads): The mat is set into a dirt collection tray recessed into the floor, which also acts as the edge trim. The required installation depth is 80 mm. The system can be connected directly to the drainage pipe so that sand, dust and rainwater are carried away; inside, cross members provide a stable bearing surface, or gratings instead where higher load requirements apply. No angle frame is used in this option.
In the STABLE series, all three installation options are compatible with underfloor heating in the entrance area. If installation screws are used for fixing, check the routing of the heating pipes beforehand.
Cassette brush: black, grey, brown, red
Support profile: natural aluminium, black anodised or powder-coated
Other inserts in the STABLE 17/30 profile: rib carpet (overall height 25 mm, Zones 2–3) and vinyl rubber (overall height 24 mm, Zones 1–3)
All entrance mats are manufactured in any size and shape required. Round and segmented shapes are produced by precisely cutting rectangular mats to size – the aluminium profiles are not bent. The mat can be rolled up, both for transport and for cleaning the substrate.
| Properties ‘Recessed entrance mat with brush insert 17/30 mm STABLE and aluminium angle frame’ | |
|---|---|
| Application | Indoor and outdoor use (Zones 1, 2, 3; recommended as Zone 1) |
| Cleaning insert | Cassette brush |
| Footfall | up to 10,000 people per day and more |
| Profile height | 17 mm |
| Overall height | 27 mm |
| Profile width | 30 mm |
| Profile spacing | 4–8 mm, spacer sleeves |
| Support profile | Double-supported rectangular hollow aluminium profile with internal reinforcing webs, 17 × 30 mm |
| Weight per m² | 16 kg/m² (mat); aluminium angle frame 0.36 kg/m²; dirt collection tray 14 kg/m² |
| Profile colour | Natural aluminium, black anodised or powder-coated |
| Connection | Stainless steel wire rope connection Ø 3 mm / minimum breaking load 5.06 kN, fastening: chrome-plated brass screw clamp (DIN EN ISO 9001:2015); EPDM connectors and mat connectors not available in this series |
| Also suitable for | Stadiums, arenas, exhibition grounds, congress centres, airports, major railway stations and shopping centres (recommended clean-off zone 48–64 m²); railway stations, universities, hospitals, and resort and spa centres (27–36 m²); office complexes, hotels, government agencies, public authorities, schools and public facilities (12–18 m²) |
| Installation | Option A – aluminium angle frame 21 mm, minimum installation depth 21 mm; alternatively stainless steel angle frame 25 mm; Option B – ramp profile 17 mm; Option C – dirt collection tray, installation depth 80 mm; all options compatible with underfloor heating |
| Can be combined with | RIPS/BÜRSTE STABLE 17/30 1:1 (rib and brush inserts in a 1:1 ratio; 27 mm, R12), GUMMI/BÜRSTE STABLE 17/30 1:1 (rubber and brush inserts in a 1:1 ratio; 27 mm, R11), RIPS/GUMMI/BÜRSTE STABLE 17/30 1:1:1 (rib, rubber and brush inserts in a 1:1:1 ratio; 27 mm, R11); MIX combination of profile widths with STABLE XL 17/50 |
| Properties | Slip resistance R13 (DIN 51130), reaction to fire class Bfl-s1 (DIN EN 13501-1), dynamic load capacity 2000 kg/dm², underside EPDM impact sound insulation 3 mm, insert material Moplen EP440G, production standard ISO 2424, use class 23 – domestic (EN ISO 10874), colour fastness to light ≥ 5 (ISO 105-B02), repels coarse dirt, sound-insulating, dimensionally stable, weather-resistant, can be rolled up, easy to clean, available in any size and shape; not suitable for forklift trucks or construction hoists |
| Warranty | 8 years on the aluminium construction, 2 years on rubber products |
| Accessories | Aluminium angle frame 21 mm (wall thickness 3–5 mm, black anodised on request), stainless steel angle frame 25 mm, dirt collection tray (wall thickness 3 mm, installation depth 80 mm), ramp profile 17 mm, Laser Cut Design; mat connectors not available for this series |