Recessed entrance mat STABLE 11/30 mm with rib insert and aluminium angle frame: 18 mm low-profile, R11, Cfl-s1, 2000 kg/dm², 6 colours. Order now, made to measure.
The recessed entrance mat STABLE 11/30 with rib insert is the indoor solution for shallow mat wells, with a reinforced support profile. The double-supported rectangular hollow aluminium profile with internal reinforcing webs (profile height 11 mm × profile width 30 mm) has a permissible dynamic load capacity of 2000 kg/dm². The finished mat is only 18 mm high and, with the aluminium angle frame, requires an installation depth of just 14 mm. The polypropylene rib carpet absorbs moisture from footwear and retains fine dirt such as sand and dust – the classic task of the final cleaning stage inside the building. The insert is classified as slip-resistant to R11 under DIN 51130 and has a reaction to fire class of Cfl-s1 under DIN EN 13501-1; the 1.5 mm EPDM impact sound insulation on the underside ensures low-noise walking. In the precisely fitting aluminium angle frame, the aluminium profile mat sits flush in the mat well and meets the surrounding floor covering without creating a trip hazard.
Within the 11/30 profile, rib carpet is the only insert that absorbs moisture instead of draining it away, and also the only one restricted to Zones 2 and 3: the rubber insert variant (overall height 17 mm, R10) and the brush insert variant (20 mm, R13) are approved for use in all three zones, but remove coarse dirt mechanically without drying the soles. As a Zone 3 mat indoors, the rib insert is therefore the right choice; in uncovered outdoor areas, however, it cannot be used. Compared with the aluminium profile mat with rib insert STANDARD 12/30, which has the same overall height of 18 mm and covers the same footfall of up to 50 people per day, this version offers 2000 instead of 1200 kg/dm², EPDM rather than polypropylene impact sound insulation, a documented reaction to fire class of Cfl-s1, black anodised or powder-coated support profiles and an optional stainless steel frame with a frame height of 15 mm. If footfall exceeds 50 people per day or a dirt collection tray is required, RIPS STABLE 17/30 (rib insert) with an overall height of 25 mm is the right choice.
The rib insert is approved for use only indoors and in covered outdoor areas – Zones 2 and 3. This restriction applies to all series and therefore also to the STABLE series, whose support profile itself can be used both indoors and outdoors. The rib carpet is not designed for permanently uncovered outdoor areas: it absorbs moisture from footwear – up to 80 % – but is not intended for permanent wetness.
Its strength lies in Zone 3 inside the building: here, fine residual dirt such as sand and dust is removed from footwear, the remaining moisture is absorbed and the soles are dried. The 11/30 profile is designed for a footfall of up to 50 people per day. Typical buildings in this footfall category are family homes, small offices and medical practices; a clean-off zone of 4–6 m², laid as a single zone, is recommended. For entrance areas with higher footfall, profile heights of 17–20 mm are intended.
An Alukraft entrance mat is installed in exactly one of three mutually exclusive ways. This version is configured for installation Option A – fitting with angle frame: the aluminium angle frame with a frame height of 14 mm is set into the mat well; the mat sits flush inside it and is level with the surrounding floor covering. The required installation depth is 14 mm and corresponds to the height of the selected frame. A ramp profile is not used in this option.
The frame is assembled with the supplied corner connectors and straight connectors; floor anchors allow drill-free installation followed by levelling and grouting in with cement mortar, with pre-drilling for fixing screws on request. Alternatively, the frame is also available in stainless steel (chromium-nickel) with a frame height of 15 mm; stainless steel frames are supplied as four elements and connected on site. A full precise fit is only guaranteed when the Alukraft entrance mats intended for the frame are used.
Alternative installation option for this profile:
Note on underfloor heating: For the STABLE series, the available installation options are compatible with underfloor heating in the entrance area. If installation screws are used for fixing, check the routing of the heating pipes beforehand.
| Properties ‘Recessed entrance mat STANDARD 11/30 mm with rib insert and aluminium angle frame’ | |
|---|---|
| Application | indoor and covered outdoor use (Zones 2, 3; recommended as Zone 3) |
| Cleaning insert | polypropylene rib carpet (production standard ISO 2424) |
| Footfall | up to 50 people per day |
| Profile heights | 11 mm |
| Overall heights | 18 mm |
| Profile width | 30 mm |
| Profile spacing | 4–8 mm, spacer sleeves |
| Support profile | double-supported rectangular hollow aluminium profile with internal reinforcing webs, 11 × 30 mm |
| Weight per square metre | 11 kg/m² (mat); aluminium angle frame 0.26 kg/m² |
| Profile colour | natural aluminium, black anodised or powder-coated |
| Connection | stainless steel wire rope connection Ø 2 mm / minimum breaking load 3.43 kN, fastening: chrome-plated brass screw clamp (DIN EN ISO 9001:2015); EPDM connectors not available in this series |
| Also suitable for | family homes, small offices and medical practices; recommended clean-off zone 4–6 m² as a single zone |
| Installation | Option A – aluminium angle frame 14 mm, minimum installation depth 14 mm, or stainless steel angle frame 15 mm; alternatively Option B – ramp profile 11 mm; Option C – dirt collection tray not available |
| Can be combined with | RIPS/GUMMI STABLE 11/30 1:1 (rib and rubber inserts in a 1:1 ratio; 18 mm, R10), RIPS/BÜRSTE STABLE 11/30 1:1 (rib and brush inserts in a 1:1 ratio; 20 mm, R12), RIPS/GUMMI/BÜRSTE STABLE 11/30 1:1:1 (rib, rubber and brush inserts in a 1:1:1 ratio; 20 mm, R11); MIX combination of other profile heights or widths not in the range for this profile |
| Properties | slip resistance R11 (DIN 51130), reaction to fire class Cfl-s1 (DIN EN 13501-1), dynamic load capacity 2000 kg/dm², underside: EPDM impact sound insulation 1.5 mm, use class 23 – domestic (EN ISO 10874), colour fastness to light ≥ 5 (ISO 105-B02), colour fastness to rubbing ≥ 4 (ISO 105-X12), colour fastness to water ≥ 4 (ISO 105-E01), moisture-absorbing, hard-wearing, sound-insulating, can be rolled up, easy to clean, available in any size and shape |
| Warranty | 8 years on the aluminium construction, 2 years on rubber products |
| Accessories | aluminium angle frame 14 mm (wall thickness 3–5 mm), stainless steel angle frame 15 mm, ramp profile 11 mm, Laser Cut Design; dirt collection tray and mat connectors not available for this profile |